Our years of expertise lets us assist engineers in a consultative manner. We are committed to finding you the right pressure sensors for your needs. If we think you are overdesigning (thus overpaying) for your requirements, we will tell you!
148 Items found
4515 is a small, ceramic-based PCB mounted pressure transducer from Measurement Specialties. This low cost, high performance transducer is fully calibrated and temperature-compensated with a total error and of less than 1% over the compensated range.
4515DO is a small, ceramic-based PCB mounted pressure transducer from Measurement Specialties with a digital output. This low cost, high performance transducer is fully calibrated and temperature-compensated with a total error and of less than 1% over the compensated range. The sensor operates from a single supply of either 3.3 or 5.0 VDC. Packaging includes side port, top port, and manifold mount versions in either differential or gauge models. Calibration ranges from 2" to 30" of water. 1/8" barbed pressure ports mate securely with 3/32" ID tubing.
4525DO is a small, ceramic-based PCB mounted pressure transducer from Measurement Specialties. This low cost, high performance transducer is fully calibrated and temperature-compensated with a total error and of less than 1% over the compensated range.
The 86BSD is a small profile, media compatible, piezoresistive silicon pressure sensors packaged in a 316L stainless steel housing. This digital output pressure sensor supports I2C and SPI interface protocols, may come in a 3.3 or 5.0 VDC supply voltage and is designed for O-ring mounting.
The AG3xF is an absolute pressure sensor for 0-115 kPa. The low-level signal from the sensor is amplified, temperature-compensated, calibrated and converted to a high-level analog output signal proportional to the applied pressure. This sensor is a replacement for the obsolete XFAM pressure sensor.
The AH3 gauge pressure sensor series has a smooth analog amplified and temperature-compensated output with low noise. The AH3 has a unique single point pressure threshold detection.
The AL4 pressure sensor is a digital output low pressure sensor. It is composed of a silicon piezoresistive pressure sensing chip and a signal conditioning integrated circuit.
The MS5561 is a SMD-hybrid device including a precision piezoresistive pressure sensor and an ADC-Interface IC. It uses a 3-wire serial interface for communication.
AMS3011 is a series of robust pressure transmitters in a matchbox-size IP67 metal package. This series is suitable for high precision measurements in industrial indoor and outdoor applications as well as medical instrumentation.
AMS5105 Series combines high precision OEM pressure sensors with programmable pressure switches in one package. AMS5105 has an analog voltage output and two independent logic switching outputs.
AMS5612 is a series of unamplified, laser-trimmed pressure sensors with a differential, ratiometric mV output signal. They are designed for constant voltage excitation with a supply voltage up to 20 V. All AMS5612 are calibrated and temperature compensated from 0 - 60°C.
AMS5812 pressure sensors are a series of high-precision OEM sensors with an analog 0.5-4.5 V output and a digital I2C interface.
AMS5915 is calibrated and compensated for a wide temperature range of -25 to +85 C. A very low power supply of 3.0 to 3.6 V is used.
AMS6915 is a series of high precision OEM pressure sensors with a digital I2C interface in a compact DIL package. The series is especially suitable for low and medium differential pressure measurements in applications that require a small size.
AMS 6916 is an OEM pressure sensors series offering an analog voltage output in a compact DIL package for assembly on printed circuit boards.
The AP/AG pressure sensor series from Fujikura is composed of a silicon piezeoresistive pressure sensing chip and a signal conditioning integrated circuit. The low-level signal from the sensing chip is amplified, temperature-compensated, calibrated and finally converted to digital data that is proportional with the applied pressure. Gauge pressure sensor. The AG version is in a surface mount package. Pressure ranges include: 25 kPa, 50 kPa, 100 kPa, 200 kPa, 500 kPa and 1 MPa. 3 models are available: AP2/AG2 with compensated analog output, AP3/AG3 analog output with threshold detection, and AP4/AG4 with a digital output.
This new ASIC sensor from Fujikura comes with a calibrated, temperature-compensated output in various pressure ranges from 0-25 kPa up to 0-1000 kPa. The most significant advantage of this part is the extremely high accuracy of 1.5% full-scale.
This new ASIC sensor from Fujikura comes with a calibrated, temperature-compensated output in various pressure ranges from 0-25 kPa up to 0-1000 kPa. The most significant advantage of this part is the extremely high accuracy of 1.5% full-scale and the ability for threshold detection.
The AP4/AG4 gauge pressure sensor series is composed of a silicon piezeoresistive pressure sensing chip and a signal conditioning integrated circuit. The low-level signal from the sensing chip is amplified, temperature-compensated, calibrated and finally converted to digital data that is proportional with the applied pressure.
Low Power Pressure Sensor: The MS5534 is a SMD-hybrid device including a piezoresistive pressure sensor and an ADC-Interface IC.
The CCD 53 Series are fully compensated and amplified pressure sensors. Featuring a rigid ceramic substrate, the CCD 53 Series delivers excellent thermal and long term stability.
The CCD 53 Series are fully compensated and amplified pressure sensors. Featuring a rigid ceramic substrate, the CCD 53 Series delivers excellent thermal and long term stability.
The CCD 53 Series are fully compensated and amplified pressure sensors. Featuring a rigid ceramic substrate, the CCD 53 Series delivers excellent thermal and long term stability.
The CCD 53 Series are fully compensated and amplified pressure sensors. Featuring a rigid ceramic substrate, the CCD 53 Series delivers excellent thermal and long term stability.
The CCD 54 Series are fully compensated and amplified pressure sensors. Featuring a rigid ceramic substrate, the CCD 54 Series delivers excellent thermal and long term stability.
The CCD 54 Series are fully compensated and amplified pressure sensors. Featuring a rigid ceramic substrate, the CCD 54 Series delivers excellent thermal and long term stability.
The CCD 54 Series are fully compensated and amplified pressure sensors. Featuring a rigid ceramic substrate, the CCD 54 Series delivers excellent thermal and long term stability.
The CCD 54 Series are fully compensated and amplified pressure sensors. Featuring a rigid ceramic substrate, the CCD 54 Series delivers excellent thermal and long term stability.
The CCD 55 Series is a smart pressure sensor with a calibrated and amplified analog output. The series features a flat surface ideal for interfacing to a manifold and sealing by o-rings.
The CCD 55 Series is a smart pressure sensor with a calibrated and amplified analog output. The series features a flat surface ideal for interfacing to a manifold and sealing by o-rings.
A ceramic base plate working as a flush diaphragm using the piezoresistive principle composes the Metallux differential pressure sensors. The Wheatstone bridge is screen-printed on one side of the base plate, which is then glued to a ceramic ring to allow proper diaphragm flexing. A special coating protects the bridge, which can therefore be exposed directly to the medium being measured.
The ME600 are monolithic gauge ceramic pressure sensors using piezoresistive technology. The Wheatstone bridge is screen printed directly on one side of the ceramic diaphragm by means of thick film technology. The diaphragm's opposite side can be exposed directly to the medium being measured.
The ME506 is a piezo resistive ceramic pressure sensor. The ME506 is available for absolute- and gauge pressure measurement.
The ME501/505 are piezoresistive ceramic pressure sensors. The measuring bridge is printed directly on one side of the ceramic diaphragm by means of thick film technology.
The ME509 is a piezo resistive ceramic pressure sensor specially designed for level measurement applications. The rear side of the flat diaphragm can be exposed directly to the medium without any additional protection due to the excellent chemical resistivity of the ceramic.
ME77X are two-piece piezoresistive ceramic pressure sensors with three different output signal options: ratiometric 0.5-4.5V, non-ratiometric 0-10V or 4-20 mA.
The new ME780 family uses a hybrid technology and Metallux's chip-on-board expertise to have signal conditioning directly integrated on top of the sensor.
Model 164 Series are low range differential pressure transducers and transmitters. It features a stainless steel enclosure and a plastic top. The additional small cap covers the terminal screws and adjustment holes. The pressure range covers from 0.1"WC to 100"WC, unidirectional or bidirectional.
The CPS120M series tire pressure monitoring sensor module is a direct tire pressure monitoring system. By installing four tire pressure monitoring sensors in the each tire, it converts the air pressure signal into an electrical signal and transmits the signal through a wireless transmitter.
The CPS121 is an absolute pressure sensor solution with a fully-calibrated pressure and temperature-compensated digital output for pressure ranges from 300-1200 mbar (30-120 kPa). Excellent accuracy of ±1.7 mbar and an operating supply voltage range 2.3V to 5.5V targets battery and other low-power applications.
Model 161 Series are low-range differential pressure transducers and transmitters. Each unit features a stainless steel pressure sensor, a stainless steel back cover, and a plastic enclosure.
Model 167 Series are low range differential pressure transducers and transmitters. It was specially designed for 35mm Din Rail Mounting, which dramatically reduces the required mounting space and installation costs.
ES Systems has developed a series of board mountable capacitive pressure sensors targeting a variety of markets requiring high resolution and accuracy for absolute, gauge or differential pressure measurements. These sensors have excellent resolution with an analog (0-3.3V), PWM, SPI or I2C interface.
ES Systems has developed a series of capacitive pressure sensor transducers for absolute pressure measurements. Each module integrates an oil-filled pressure capsule equipped with a medium isolation diaphragm that protects the MEMS capacitive pressure sensor die.
ES Systems has developed a series of media-isolated pressure transmitters suitable for applications with harsh environmental conditions where resistance to corrosive fluids or gases is required. Each sensor integrates a MEMS capacitive pressure sensor die, and a CMOS ASIC for signal conditioning. State-of-the-art accuracy and resolution are provided. The total overall error including thermal offsets is lower than ±0.25% FS.
FAM, absolute pressure, surface mount package or termain leads
FDM pressure sensor is a differential pressure sensor with a millivolt uncalibrated output for various pressure ranges. Surface-mount package. Various pressure ranges are available from 2 psi up to 120 psi.
FGM-3 Surface Mount Package (3 mm tube length), best used directly attached to manifold and sealed with an O Ring.
FHM is a gauge pressure sensor with a horizontal side port for use with silicon tubing or to directly attach to a manifold. Various calibration ranges are available from 2 psi up to 120 psi. The FHM has a millivolt unamplifed output.
FPBS Series Absolute Pressure With mV Output
FPM (Gauge) Package (8 mm tube length), best used with silicon tubing or directly attached to manifold.
FPM (Absolute) Package (8 mm tube length), best used with silicon tubing or directly attached to manifold. Also available as FAM surface mount sensors (no port); please ask!
FPN/FGN (Gauge) Package (8 mm tube length) with millivolt uncalibrated output. Best used with silicon tubing or directly attached to manifold.
Servoflo is pleased to announce a new customer case study. Hickok Incorporated is using the Fujikura AP Series in its EVAP Leak Tester, a portable system designed specifically for measuring and reporting leaks in automobile evaporative emissions systems.
The HTC52 Series is a miniature, robust pressure sensor with calibrated and temperature compensated SPI, I2C or analog output. A variety of output configurations, including resolution, sampling rate, output interface are available to provide a simple and ready to use solution for a wide range of applications.
The HTS1510 Series is a surface-mountable package with both digital and analog outputs available. Its backside pressure measurement provides excellent compatibility with wet, corrosive media. It is ideal for integration on a control board.
Model 162 Series are low-range differential pressure transducers and transmitters. Each unit features a stainless steel pressure sensor, a stainless steel back cover, and a plastic enclosure.
Model 166 Series are low range differential pressure transducers and transmitters. It features a flame retardant plastic enclosure with a metal backing. The unique design allows it to be used for outdoor environments and with easy access to zero and sensitivity adjustments. The pressure range covers from 0.1"WC to 100"WC, unidirectional or bidirectional.
Model 178 Series are low-range differential pressure transmitters. Each unit features a push-activated ZERO function and an associated LCD display. With a convenient push button switch, the zero calibration is easy, signficantly reducing time and cost for users.
Model 178A Series are low-range differential pressure transmitters. Each unit features a 3 1/2 digit LCD to show the pressure, also a push button switch (inside) for zero pressure calibration.
Model 179 Series are low-range differential pressure transmitters. Each unit features a push-activated pressure equalization button, two Zero push button switches, a LCD and two LED lamps.
Model 165 Series are low range differential pressure transducers and transmitters. It features a stainless steel enclosure and a plastic top. The additional small cap covers the terminal screws and adjustment holes. The pressure range covers from 0.1"WC to 100"WC, unidirectional or bidirectional.
Model 175 Series are low-range differential pressure transducers and transmitters. Each unit features a push-activated ZERO function and an ssociated LED lamp indicator. With a convenient pushbutton, the zero calibration can be performed without any additional equipment.
The LP Series pressure sensors is a surface mountable 8 pin design available in both uncompensated and compensated output configurations. The compensated LP Series versions include both high-accuracy analog (LP1410) or digital ratiometric signal output options (LP1420) with each version having full compensation for offset, temperature and span variability.
The M3200 pressure transducers are suitable for measurement of liquid or gas pressure, even for difficult media such as contaminated water, steam and mildly corrosive fluids. The transducer pressure cavity is machined from a solid piece of 17-4PH stainless steel.
The MAP 36A Series has been developed specifically for manifold pressure measurement in automobile engines. These sensors are rugged, robust and fully temperature-compensated.
The MAP 36 Series are fully compensated and amplified pressure sensors. The series can be ordered with a variety of port options. The series is an ideal manifold absolute pressure sensor or MAP sensor.
The MAP 36 Series are fully compensated and amplified pressure sensors. The series can be ordered with a variety of port options. The series is an ideal manifold absolute pressure sensor or MAP sensor.
The MAP 36 Series are fully compensated and amplified pressure sensors. The series can be ordered with a variety of port options. The series is an ideal manifold absolute pressure sensor or MAP sensor. Based on Sensormate's proprietary sensor platform, the MAP 36 Series incorporates a silicon MEMs pressure sensor with the latest ASIC technology.
The MAP 36 Series are fully compensated and amplified pressure sensors. The series can be ordered with a variety of port options. The series is an ideal manifold absolute pressure sensor or MAP sensor. Based on Sensormate's proprietary sensor platform, the MAP 36 Series incorporates a silicon MEMs pressure sensor with the latest ASIC technology.
The MAP 36 Series are fully compensated and amplified pressure sensors. The series can be ordered with a variety of port options. The series is an ideal manifold absolute pressure sensor or MAP sensor. Based on Sensormate's proprietary sensor platform, the MAP 36 Series incorporates a silicon MEMs pressure sensor with the latest ASIC technology.
The MCD70 is a solid state, piezoresistive pressure sensor packaged in a ceramic substrate with SMD, DIP or SIL configuration. It is intended for low pressure applications where both low-cost and extreme long term offset stability are required.
The MCD70A is a smart pressure sensor with an amplified analog output. Digital compensation of sensor offset, sensitivity, temperature drift and nonlinearity is accomplished in factory via an internal DSP running a correction algorithm with calibration coefficients stored in an on-chip EEPROM.
The MCD70D is a smart pressure sensor with an amplified digital output in I2C and OWI. Digital compensation of sensor offset, sensitivity, temperature drift and nonlinearity is accomplished in factory via an internal DSP running a correction algorithm with calibration coefficients stored in an on-chip EEPROM.
MDM290 is a piezoresistive differential pressure sensor with a stainless steel isolated diaphragm. Accepting a high static pressure, the MDM290 is stable and reliable.
The MDM3051 is an industrial pressure transmitter with a HART protocol and 4-20 mA 2 wire output of pressure.
The MDM490 uses a piezoresistive differential pressure sensor as its sensing element. Silicon oil is filled in between die and two diaphragms.
The MDM492 is a low differential pressure transmitter with a high performance sensor and amplifier circuit. The output is a 4-20mA current signal.
ME900 are ready to use monolithic pressure transducers made with a 9 mm diameter ceramic cell mounted in a dedicated housing. This groundbreaking sensor uses the piezoresistive principle where the Wheatstone bridge is screen-printed directly on one side of the ceramic diaphragm via thick film technology.
NEW!! The FSP1000 Series is an ultra low flow through differential pressure sensor with ranges from ±250 to ±500 Pa (±1.0 to ±2.0 H2O). Highly sensitive at low differential pressure, the FSP1000 has temperature compensation with a digital I2C output or analog output with a fast response time of 5.0 msec. The sensor is fully compensated for altitude. The supply voltage is 3.0 to 3.6 VDC.
The MF4600 Series mass flow meters are made with Siargo's proprietary MEMS sensing technology. It applies or clean and dry gas metering and control. The meter is designed with the structure of a rotameter but with the full capability of digital gas mass flow metrology and LED display.
The MS5607-B is a new generation of high resolution altimeter sensors from TE Connectivity with SPI and I2C bus interface.
AMS4711/4712 is a series of miniaturized pressure transmitters suitable for industrial applications and high precision measurements. These pressure transmitters are powered with 8-36 VDC and provide an output of 0-5VDC (AMS4711 or 4-20mA (AMS4712). They are calibrated and temperature compensated in a wide temperature range of -25C to +85C.
The MS5540 is a SMD-hybrid device including a precision piezoresistive pressure sensor and an ADC-Interface IC.
The MS5541 is the miniature version of the popular MS5535 pressure sensor module. It contains a precision piezoresistive pressure sensor and an improved version of the 15 Bit Micropower Sensor interface IC known from the MS5535.
TE Connectivity has now introduced the MS554C-60 High Pressure version of this model which measures from 0-30 bar absolute.
ME75X are monolithic piezoresistive ceramic pressure sensors with three different output signal options: ratiometric 0.5-4.5V, non-ratiometric 0-10V or 4-20 mA.
ME790 and MEP790 are monolithic piezoresistive ceramic pressure sensors. The Wheatstone bridge is screen printed directly on one side of the ceramic cell by means of thick film technology and signal conditioning electronics generate 0.5 - 4.5V ratiometric output. Pressure and temperature calibration are done electronically with the on-board ASIC and can be performed in bar (ME790) or in psi (MEP790).
MPM180/MPM185 is a piezoresistive pressure sensor with TO-8 housing which is built with advanced ion implantation and micro-mechanical working technology to produce a precise Wheatstone Bridge.
Various versions of the general MPM280 are available:
MPM281 is a highly stable OEM piezoresistive pressure sensor with precise compensation. It uses highly stable silicon die, with an outer diameter of 29mm 316L stainless steel housing.
MPM283 piezoresistive pressure sensor is an OEM pressure sensor with a stainless steel isolated diaphragm. With integrated construction, high endurance, stability and reliability, the MPM283 is used specifically for middle to high pressure measurement.
The MPM3808 is a piezoresistive OEM pressure sensor with 316L stainless steel corrugated diaphragm and isolated oil-filled construction. The sensing package utilizes silicone oil to transfer pressure from the 316L stainless steel diaphragm to the sensing die. The sensor outputs pressure and temperature via I2C or SPI interface.
MPM416 measure liquid static pressure accurately which is positively proportional to liquid depth, transmitting a pressure signal into a standard current/voltage output signal by amplifier circuit board.
The MPM426 & MPM436 use high performance liquid pressure sensors as sensing elements which measure liquid static pressure that is positively proportional to level depth, and transform pressure signals into standard current/voltage output signals by an amplifier circuit to measure depth level accurately.
The MPM4700 liquid level measurement sensor has full stainless steel construction and full-sealed submersible pressure transmitter with high accuracy.
The MPM4730 pressure transmitter is a highly accurate and stable, intelligent pressure transmitter. It uses digital temperature compensation, non-linearity correction techniques, and advanced transmitter production processes.
The MPM480 pressure transmitter uses a piezoresistive OEM pressure sensor with an isolated stainless steel diaphragm as its signal sensing element.
The MS4425 & MS4426 are temperature-compensated piezoresistive silicon pressure sensors intended for cost-sensitive applications where excellent performance and long-term stability are required. The MS4425 have tubes parallel to the printed circuit board with either a differential, gauge or absolute configuration.
MS4525 is a small, ceramic-based PCB mounted pressure transducer from Measurement Specialties. This low cost, high performance transducer is fully calibrated and temperature-compensated with a total error and of less than 1% over the compensated range.
The MS5803 is a new generation of high resolution altimeter sensors with SPI & I2C interface. There are various models up to 30 bar. The sensor module includes a high linearity pressure sensor with an ultra low power 24 bit ADC with internal factory calibrated coefficients.
The MS5805-02BA is a new generation of high resolution altimeter sensors from TE Connectivity with I2C bus interface. It is optimized for altimeters and variometers with an altitude resolution of 20 cm.
The MS5806-02BA is a new generation of high resolution altimeter sensors with SPI and I2C interface. It is optimized for altimeters and variometers with an altitude resolution of 20 cm.
The MS5837 is a new generation of high resolution pressure sensors with I2C bus interface for depth measurement systems with a water depth resolution of 2 mm for the 30BA model (calibrated 0-30 bar). The MS5837-02BA01 model is calibrated from 3-1200 mbar and has an altitude resolution at sea level of 13 cm of air.
The MS5839 is an ultra-compact (3.3 x 3.3 x 2.75 mm) digital altimeter that is optimized for applications where chlorine and saline are present. the robust, gel-filled design of the MS5839 enables operation in harsh media environments while providing accurate and reliable digital measurements.
The MS5840 is an ultra-compact micro altimeter. It is optimized for altimeter and barometric applications. The altitude resolution at sea level is 13 cm of air. The sensor module includes a temperature measurement. The MS5840 can be interfaced to any microcontroller via I2C. The gel protection and antimagnetic stainless steel cap makes this barometric pressure sensor water resistant.
Model 168 Series are low range differential pressure transducers and transmitters with NEMA 4 (IP-65) rated aluminum enclosures. They are very rugged and reliable, good for many industrial applications. The pressure range covers from 0.1"WC to 100"WC, unidirectional or bi-directional.
The RS Series uncompensated packaged pressure sensor is designed for the application of a wide range of pressures to the backside of the sensing element. The RS is a flexible platform with excellent media compatibility. The technology is a piezoresistive Wheatstone bride with a chemically etched silicon diaphragm.
Using a high quality silicon MEMs pressure sensor as the sensing element, the SCD Series provides a compact footprint for the tightest space requirements. It is particularly well-suited for high volume OEM applications that require the flexibility of either gauge or absolute pressure sensors. The SCD51 Series can be specified with pressure ranges from 5-100 psi.
Servoflo and Fujikura are pleased to offer pressure sensors specifically designed for non-invasive blood pressure measurement. These sensors are specially calibrated AP3/AG3 models.
Using a high quality silicon MEMs pressure sensor as the sensing element, the 5 psi version is widely used in blood pressure and air mattress pressure measurement where a low cost pressure sensor is critical. For higher pressures, 15 psi and 100 psi version are also available.
The SLP33A-LP Series are fully compensated, amplified gauge pressure sensors with a pressure port. Ordering options include negative pressure or bi-directional pressure ranges. The SLP33 Series incorporates a silicon MEMs pressure sensor with the latest ASIC technology.
The SLP33A-STD Series are fully compensated, amplified gauge pressure sensors with a pressure port for 5-100 psi. Ordering options include negative pressure or bi-directional pressure ranges. The SLP33 Series incorporates a silicon MEMs pressure sensor with the latest ASIC technology.
The SLP33D-LP Series are fully compensated, amplified gauge pressure sensors with a pressure port. Ordering options include negative pressure or bi-directional pressure ranges. This model has a digital output. The SLP33 Series incorporates a silicon MEMs pressure sensor with the latest ASIC technology.
The SLP33D-STD Series are fully compensated, amplified gauge pressure sensors with a pressure port for 5-100 psi. Ordering options include negative pressure or bi-directional pressure ranges. The SLP33 Series incorporates a silicon MEMs pressure sensor with the latest ASIC technology.
The SLP 35 Series are fully compensated and amplified pressure sensors. With a small footprint of 10 mm x 10.2 mm x 10 mm, these are one of the smallest available dual port pressure sensors. Applications include HVAC controllers, medical or flow instruments and pneumatics.
The SLP 35 Series are fully compensated and amplified pressure sensors. With a small footprint of 10 mm x 10.2 mm x 10 mm, these are one of the smallest available dual port pressure sensors. Applications include HVAC controllers, medical or flow instruments and pneumatics.
The SLP 35 Series are fully compensated and amplified pressure sensors. With a small footprint of 10 mm x 10.2 mm x 10 mm, these are one of the smallest available dual port pressure sensors. Applications include HVAC controllers, medical or flow instruments and pneumatics.
The SLP 35 Series are fully compensated and amplified pressure sensors. With a small footprint of 10 mm x 10.2 mm x 10 mm, these are one of the smallest available dual port pressure sensors. Applications include HVAC controllers, medical or flow instruments and pneumatics.
The SM1111/SM1131 are absolute pressure sensors for barometric air pressure measurement (BAP). The sensors include a piezo-resistive pressure sensor die and a signal processing IC to perform amplification and thermal compensation of the pressure sensor output. The SM1111 have a pressure range of 15-115 kPa with a ratiometric analog output.
The SM1XXX Series is a digital/analog pressure sensor for 15 psi with a digital, fully-conditioned in a SOIC-16 package with either dual vertical or horizontal ports. It is available in both compound gauge, differential pressure or asymmetric configurations.
The SM4XXX Series is a digital and analog, medium pressure MEMS sensor family offering state-of-the-art pressure transducer and CMOS mixed signal processing technology to produce a digital, fully-conditioned, multi-order pressure and temperature-compensated sensor in SOIC-16 package with a dual vertical porting option.
The SM5420 is a small outline SO-8 packaged pressure sensor. The sensor is intended for high volume applications where cost is a critical factor, such as consumer tire pressure gauges or automotive tire pressure monitoring.
The SM5G-GG Series is a small outline SO8 packaged pressure sensor that incorporates new SM30G MEMS piezoresistive pressure sensing die. The SM5G-GG Series has been optimized to provide the highest possible accuracy for a package of this size. Performance is achieved through careful resistor placement and mechanical configuration along with advanced MEMS processing.
The SM5XXX, SM6XXX, and SM7XXX are ultra low pressure MEMS sensor families offering state of the art pressure transducer technology and a CMOS mixed signal processing technology to produce a digital or analog, fully-conditioned, multi-order pressure and temperature-compensated sensor in JEDEC standard SOIC-16 packaging with dual ports (horizontal or vertical).
The SM6250 Series combines state-of-the-art sensor technology with CMOS mixed-signal processing technoogy in a low profile SOIC-16 package with dual holes. Pressure is measured from the backside, while additional protection to the electronic circuitry is provided by protective gel on the topside.
SM6295 is an amplified gauge pressure sensor calibrated from 0-40 cmH2O. The sensor has state-of-the-art mixed signal processing to provide a fully calibrated and temperature compensated pressure sensor. The sensor can be mounted directly on a printed circuit board without the need for additional circuitry. The sensor is pressurized from the backside to protect topside electronics.
The SM6841 is a small outline SO-8 packaged pressure sensor that incorporates SMI's new piezoresistive pressure sensing die. This sensor is intended for high volume applications where cost is a critical factor.
The SM6844 Series is an absolute pressure sensor family offering state-of-the-art pressure transducer technology and CMOS mixed signal processing technology to produce an analog, fully-conditioned, pressure and temperature-compensated sensor in JEDEC standard SOIC-16 packaging with a single horizontal porting option.
The SM923X Series are digital, ultra low gauge pressure sensors for extremely low air pressures. 3 calibration ranges are available:
In addition, users have a choice of accuracies when ordering - either 3%FS, 2.5% FS or 1.5% FS after autozero. The sensors have a 16-bit I2C digital pressure calibrated and temperature-compensated output. The SM923X Series have a standard SOIC-16 package with a dual vertical port.
The SM9333/9336 are digital, ultra-low pressure sensors offering state-of-the-art MEMS pressure transducer technology and CMOS mixed signal processing to produce a digital, fully-conditioned, multi-order pressure and temperature-compensated sensor in JEDEC standard SOIC-16 package with a dual vertical porting option. It is available as a differential pressure sensor.
The SM9543 Series is an ultra low differential pressure sensor family offering state-of-the-art pressure transducer technology and CMOS mixed signal processing technology to produce a digital, fully conditioned, multi-order pressure and temperature compensated sensor in JEDEC standard SOIC-16 package with a dual vertical porting option.
The low pressure SM9D/SM9G series incorporates SMI's unique pressure die to achieve high performance in pressure ranges of 0.15, 0.6 & 1.5 psi full-scale in gauge or differential configurations.
The MS54XX SMD pressure sensor series is designed for pressure sensor systems with highest demands on resolution and accuracy. The device consists of a silicon micromachined pressure sensor die mounted on a 6.2 x 6.4 mm ceramic carrier protected by a metal cap.
The MS5201D is a gauge type SMD pressure sensor, suitable for applications which require relative (gauge) pressure measurements.
The MS52XX-YZ SMD pressure sensor series is designed for pressure sensor systems with highest demands on resolution and accuracy. The device consists of a silicon micromachined pressure sensor die mounted on a 7.6 x 7.6 mm ceramic carrier protected by a metal cap.
Using a high quality silicon MEMs pressure sensor as the sensing element, the SMP31 uses a vent hold for the pressure interface, resulting in a low profile. The aim of the SMP31 is to allow customers to integrate an absolute pressure sensor into their systems at costs close to that of bare pressure die.
The SMP31A Series are fully compensated high performance die in a plastic surface mount package. They are absolute pressure sensors fabricated by bonding a micromachined silicon diaphragm to Pyrex glass in a vacuum. Uniform span and offset distribution results from precise implant and etching control. The result is long-term offset stability that is suitable for barometric pressure measurement.
The SOP30 Series are uncompensated pressure sensors for 15 psi absolute pressure measurement using a small surface mount package.
Using a high quality silicon MEMs pressure sensor as the sensing element, the SPD34 Series delivers an excellent value when a gauge pressure sensor is required.
Using a high quality silicon MEMs pressure sensor as the sensing element, the SPD34 Series delivers an excellent value when a gauge pressure sensor is required.
The STD60 Series are uncompensated pressure sensors. The Series feature a metal can (TO-5) package with an optional port to provide the pressure connection.
The STD Series model 60A is an amplified silicon MEMs piezoresistive sensor in a reliable TO-5 metal can package. The sensor is suitable for mounting directly onto a printed circuit board.
The T200/T201 Series of Pressure Transducers is ideally suited for both mobile and industrial applications where space constraints require a small body size. The body is machined from a single piece of 304SS to provide added protection for the internal electronics.
The TR Series is a fully compensated, amplified output pressure sensor for harsh media and/or liquids. The sensor combines harsh MEMS piezoresistive die with state-of-the-art pressure sensor ASIC signal management.
The TVC Series is a fully compensated harsh media pressure sensor deigned to handle today's toughest pressure sensing environments with temperatures between -40°C to +150°C.
The SM5470 series pressure sensors are surface-mountable Dual-in-line packages (SOIC-16) designed for a broad range of high volume, OEM manufactures of various consumer, automotive, medical, and industrial products.
Servoflo is pleased to announce the FPWS Water Level Sensor. The FPWS is a gauge pressure sensor for -49 kPa to 68.5 kpa with a linear voltage output. The sensor is oil-filled for specific use in tank level measurement applications. Typical water exposure is tap water with or without bath or cleaning agents.
Product & Pricing Guides